Blue Spot Water

Features :

• Natural pH Correction: Uses naturally occurring, high-purity Calcite media (calcium carbonate) to raise the water's pH level.

• Self-Limiting Action: The Calcite dissolves slowly and only corrects the pH to a non-corrosive equilibrium (typically pH 7.0–7.5), preventing over-correction.

• Corrosion Reduction: Significantly reduces the corrosive properties of acidic water, protecting your entire plumbing system and water-using appliances.

• Manual Filter Head: Provides simple, user-controlled operation for backwashing and maintaining the media bed.

• Cost-Effective Solution: pH fix reacts and dissolves slowly, making it an inexpensive, long-lasting solution compared to chemical-injection systems.

• Robust Vessel: Durable FRP (Fibre-Reinforced Plastic) pressure vessel built for longevity.

What does it do:

The Complete pH Fix filter system effectively neutralizes acidic water by passing it through a bed of Calcite media. The acidic water slowly dissolves the calcium carbonate, which in turn releases beneficial calcium ions and raises the water's pH.

1. Eliminates Corrosion: By raising the pH above 7.0, it eliminates the staining of sanitary ware (sinks, tubs) caused by leaching metals like copper and lead.

2. Protects Plumbing: Slows down the likelihood of pinhole leaks and dramatically increases the lifespan of your entire water distribution system, including pipes, geysers, and appliances.

3. Enhances Water Quality: Corrects the metallic or sour taste often associated with low pH water and adds essential calcium, which is considered beneficial. This is a crucial step in whole-house water treatment.

Good to know:

• Water Hardness Increase: As the Calcite dissolves, it adds calcium to the water, which will likely increase your water's hardness. In areas with already hard water, a water softener may be recommended for installation after the pH correction system.

• Ideal $\text{pH}$ Range: This system is highly effective for water with a raw pH generally between 6.0 and 6.9. For pH levels below 6.0, mixing with a faster-reacting media (like Corosex) might be required.

• Installation Point: Typically installed as a whole-house water filter on the main water line, immediately following the pressure tank (for borehole or well systems).

• Filter Type: This is a neutralizer/acid-correcting filter—it is not a sediment or carbon filter. A pre-filter for sediment is recommended if your water contains large particles.

Specifications:

Vessel Size 8” x 44” FRP (Fibre-Reinforced Plastic)

Media Type Calcite pH Fix Media (Calcium Carbonate, CaCO3?)

Media Weight 25kgs

Filter Head Manual Controller Head

Water $\text{pH}$ Range Effective for $\text{pH}>6.0$

Application Residential/Commercial Acidic Water Treatment

Maintenance:

The pH correction media is consumed over time as it neutralizes the acid

1. Backwashing: You must perform periodic backwashing using the Manual Filter Head (usually once a week or as needed) to prevent the media from compacting (cementing) and to maintain efficient flow.

2. Media Replenishment: The Calcite media will gradually deplete and must be periodically topped up (replenished). This typically occurs every 6–18 months, depending on your water's pH level and usage.

3. Annual Check: It's recommended to check your residual water pH level annually to ensure the system is operating optimally.

What is in the box:

This complete kit provides everything you need for the filter assembly:

• Manual Controller Head: x 1

• FRP Vessel 8” x 44”: x 1

• Calcite pH Fix Media 25kgs: x 1 (Sufficient for initial fill)

• Riser Pipe: x 1

• Top and Bottom Strainers: x 1 Set

Dimensions : 

• Vessel Diameter: 8 inches

• Vessel Height: 44 inches (Total height with head is approximately 50 inches)

• Footprint: Approximately 8 inches diameter.